Titanium Foil
Titanium foil is a titanium plate, strip, roll or sheet with a thickness of less than or equal to 0.2mm. The maximum width of rolled titanium foil is about 600mm.
The width of the titanium foil is cut according to the requirements of the user.But the wider the manufacturing, the higher the productivity.
Titanium foil is mainly used in aerospace, navigation, nuclear power, electronics, chemical industry, petroleum, precision manufacturing, medical pharmaceutical and other aspects.
- Kuvaus: __________
- Eritelmät
- Kysely
Titanium foil – Preparation Method
The raw material for industrially producing titanium is mainly rutile ore or high titanium slag (containing 92% or more of Ti02). Titanium sponge production process is based on high titanium slag and petroleum coke as raw material for the production of titanium tetrachloride. Titanium sponge can be obtained by reducing refined titanium tetrachloride with magnesium or sodium in a rare gas stream.
Magnesium reduction distillation method: the proportion of high titanium slag and petroleum coke is 100 (30~33), and the mixture is broken to less than 160 mesh, and sent to the fluidized bed chlorination furnace, and the chlorine gas is passed through the bottom of the furnace, uniformly enter the reaction section of the furnace body, and react with the mixed material of high titanium slag and petroleum coke. The reaction temperature was about 850 °c. The generated titanium tetrachloride gas is discharged from the top of the furnace and enters two separator dust collectors connected in series, so that high boiling points such as iron trichloride, iron dichloride, manganese dichloride and aluminum trichloride mixed in the titanium tetrachloride gas are deposited at the bottom of the separator dust collector. The gas was reintroduced into the two sets of condensers connected in series, and the titanium tetrachloride gas was cooled to below 136 ° C. To obtain a crude titanium tetrachloride solution. The low-boiling matters, such as silicon tetrachloride, therein are distilled off by means of a float valve column distillation. After heating to 140 ° C. In a copper chip Tower, the gasified titanium tetrachloride is passed into a copper chip Tower, and the contained impurity vanadyl trichloride is reduced by copper to a low-valent chloride of vanadium. The purified titanium tetrachloride gas discharged from the top of the column was subjected to a reduction reaction with magnesium in a rare gas stream at about 900 ° C. To obtain titanium sponge. Since the resulting sponge-like titanium also contains magnesium chloride as a by-product and unreacted magnesium, the sponge-like titanium must be placed under a vacuum of 0.1 jotta 10-3 Pa, the impurities were separated from the titanium by heating to about 1000 °c.
Titanium foil – Use
titanium alloy has high strength, a large number of structural materials used in the manufacture of military supersonic aircraft, compression Components of jet engines, components of aircraft frames, housings, fire barriers, rivets, structural components of air transport equipment, there is a “space metal”; Military facilities and military ships armored plate and propeller blades. In the civilian industry, titanium and its alloys can be used in the manufacture of various pumps, Venttiilit, filtration, evaporation equipment wire mesh and various machine parts. Powdered titanium can be used as an oxygen scavenger in the electron tube manufacturing process.
Titanium foil – Safety
hazard code: flammable solid. GB4.1 class 41505. UN NO.2678 (strontium powder). IMDG CODE P. 4177, Class 4.1. Each batch of product should be divided into galvanized iron barrels lined with plastic film, and the weight of each (piece) of the drum is 70~250, and it is sealed with a large open cover. Magnesium reduction titanium must be evacuated and filled with argon in the barrel after packaging. Titanium can be protected without argon by sodium reduction. “Moisture-proof” shall be indicated on the outside of the packaging barrel. Should be stored in a ventilated, dry warehouse. Shall not be stacked in the open air, and shall not be mixed with acid, alkali and other corrosive substances. During the transport process, it is necessary to prevent rain and humidity. During loading and unloading, care should be taken to prevent breakage of the packaging barrel. Titanium tetrachloride used in the production process can make people suffering from chronic bronchitis, chronic hypertrophic rhinitis, pharyngitis. Autonomic nervous system dysfunction, increased tendon reflexes, tremor of the eyelids and hands, hyperhidrosis. Thermal burns were more difficult to heal when exposed to 10% titanium tetrachloride solution. When exposed to titanium tetrachloride smoke, wear an industrial filter gas mask. To protect the eyes and skin. If you accidentally spatter on the skin, wipe it off with cotton gauze and then wash it thoroughly with water. Production equipment should be closed and the workshop should be well ventilated. Dry powder and dry sand can be used to put out the fire, and water, foam and carbon dioxide are strictly prohibited. In case of high heat or intense combustion, explosion may be caused by water suppression.
Titanium foil is a titanium plate, strip, roll or sheet with a thickness of less than or equal to 0.2mm. The maximum width of rolled titanium foil is about 600mm.
The width of the titanium foil is cut according to the requirements of the user.But the wider the manufacturing, the higher the productivity.
Titanium foil is mainly used in aerospace, navigation, nuclear power, electronics, chemical industry, petroleum, precision manufacturing, medical pharmaceutical and other aspects.
Titanium alloy has high strength and low density, good mechanical properties, good toughness and corrosion resistance.
The two most prominent advantages of titanium are high specific strength and strong corrosion resistance, which determines that titanium must have broad application prospects in aerospace, weaponry, energy, kemiallinen, metallurgy, construction and transportation. The rich reserves provide a resource base for the wide application of titanium.
Kuvaus: __________ | Titanium foil |
Materiaali | Gr1, Gr2, Gr3,Gr4,Gr5, Gr7, Gr6,Gr9, Gr11, Gr12 ,Gr16, Gr17,Gr25TA0,TA1,TA2,TA5,TA6,TA7,TA9,TA10,TB2,TC1,TC2,TC3,TC4 |
Standardi | ASTM B265,ASME SB265,DIN17851,TiA16Zr5Mo1.5,JIS4100-2007,GB3461-2007 |
Koko | Paksuus:0.05-0.2mmWidth:3-600mm
Pituus:according to requirements |
MOQ | 100 Kilogram/Kilogrames |
Equepment used | CNC lathes, Milling machine, Machining Center,Thread rolling machine Magnetic needle polishing machine |
Ominaisuuksia | 1.high corrosion resistance2.low density
3.non-ferromagnetic 4.good biocompatibility |
Paketti | Standard export package,suit for all kinds of transport ,tai tarpeen mukaan. |
Sovellus | 1.Based on High intensity,titanium products tensile strength can be up to 180Kg/mm².2.Titanium and titanium alloy in aviation industry, is called “space metal”; Lisäksi,
in the shipbuilding industry, chemical industry, manufacturing machinery parts, telecommunications equipment, hard alloy, etc have increasingly extensive application 3.Lisäksi, because of the titanium alloy with the human body has very good compatibility, so the titanium alloy can also be artificial bone. |
Kemiallinen koostumus:
Sävellys (%) | C | N | Fe | O | H | Al | V | Ti |
GR1 | ≤0.08 | ≤0.03 | ≤0.20 | ≤0.18 | ≤0.015 | – | – | Bal. |
GR2 | ≤0.08 | ≤0.03 | ≤0.30 | ≤0.25 | ≤0.015 | – | – | Bal. |
GR5 | ≤0.10 | ≤0.05 | ≤0.30 | ≤0.20 | ≤0.015 | 5.50-6.80 | 3.50-4.50 | Bal. |
Ominaisuuksia
|
The density of titanium is 4.506-4.516g/cm^3, melting point is 1668, boiling point is 3535. Therefore Titanium have low
weight,excellent high strength and nonmagnetic festures, low density, excellent corrosion resistance features, high specific strength and high temperature resistance features, so it is widely used in chemical industry field, medical field, electronics manufacture, mechanical parts field, automobile industry, and aerospace field, jne. |
Aiheeseen liittyvät tuotteet
-
Lue LisääPikakatselu
Alumiinikäämi
Alumiinikäämi on valssattu tuote, valmistettu jatkuvan nauhan kelatussa muodossa, ja sillä on sisähalkaisija ja ulkohalkaisija. ID alkaen50mm - 1000mm. Alumiiniseoslaatu, mukaan lukien 1xxx, 2xxx, 3xxx, 4xxx, 5xxx, 6xxx, 7xxx, 8xxx. Mutta yleisin on 1050, 3003, 6061 ja 5251 alumiinikela. Paksuus 0.045-80mm, leveys 60-2650mm. Alumiinikelan yleiset leveydet ovat 800 mm,1000mm, 1250mm,1450mm ja 1500mm.
Useat teollisuudenalat luottavat alumiinikeloihin erilaisissa sovelluksissa, kuten autoteollisuus, rakentaminen, Lämmönsiirto, farmaseuttinen, sähkö, ja elintarviketeollisuus. Verrattuna muihin materiaaleihin, Alumiini on paljon parempi materiaali monissa tapauksissa. Alumiinikela voidaan toimittaa tavallisella myllyviimeistelyllä, tai se voidaan harjata, ruudullinen, väri päällystetty, satiinikäsitelty ja anodisoitu. Alumiinilevy tai alumiinifolio voidaan leikata keloiksi asiakkaan vaatimusten mukaisesti.
-
Lue LisääPikakatselu
Stainless Bar
A stainless steel bar stock is often used for production line machinery or in other industrial settings where durability is required. Stainless steel round bar types can be found in many different shapes such as hexagon, aukio, or round bars. Stainless bar stock is a material that is non-corrosive, corrosion resistant, and durable. It can be used in a variety of industries such as automotive, aerospace, rakentaminen, and manufacturing.
Stainless steel bar stock is the highest quality type of stainless steel in the industry. They are made with high-quality materials that make them resistant to corrosion and other environmental conditions. The stainless bar stock also has greater tensile strength than other types of stainless steel.
Stainless steel round rod products or round bars are commonly used for manufacturing products like car rims, motorcycle rims, bicycle rims, ja enemmän. These types of bars are typically made by rolling up sheets of stainless steel into long tubes before welding them together at the ends to create round rods or round bars that can be cut into smaller pieces
-
Lue LisääPikakatselu
Copper Coils
It may seem that a copper coil is a simple piece of coiled wire that can be wound and put to use. As with any form of industrial product, copper coils have to be precisely engineered to fit an application. The winding process has to be completed with precision to ensure the proper distance between the wires and the diameter of the opening.
Each product that uses copper coils requires that a certain number of turns be made to provide the correct amount of resistance. Inaccurate calculations can lead to inefficiency and possible failure of the coil or device. For this reason, the engineers at Metal Associates guarantee that they have closely examined the specification of an application such that the diameter, spacing, wire thickness, and number of turns exactly matches the design of the product where the copper coil will be used.
-
Lue LisääPikakatselu
Titanium Sheet
Titanium plate has high corrosion resistance and specific strength, and is widely used in electric power, chemical industry, aviation parts, building materials, sports equipment, medical and other fields and is still expanding. From the point of view of use and manufacturing technology, titanium plate has low price, high performance, multiple functions, and easy production.
Jos sinulla on kysyttävää,ota rohkeasti yhteyttä sales@grandsteeltube.com
-
Lue LisääPikakatselu
Copper Strips
Copper strips have high electrical and thermal conductivity, that’s why copper strips are the best for transformer winding.
What’s more, copper strips transfer heat more effectively than other metals strips.
Copper strips are more malleable and have high tensile strength. Korroosionkestävyys, high degree stability, and heat dissipation of copper strips are superior to other metals.
Copper strips are mostly used in the electrical and electronics sectors because copper is non-magnetic and non-sparking. Copper strips are mostly used in heat exchangers, transformers winding, Lauhduttimet, and lightning conductors.
Copper strip thickness range from 0.03mm to 3.0mm. Copper strips can be manufactured in different widths and thicknesses per the customer’s requirement.
Jos sinulla on kysyttävää, ota rohkeasti yhteyttä sales@grandsteeltube.com
-
Lue LisääPikakatselu
Messinki baari
-
Lue LisääPikakatselu
Brass Strips
Brass Strip has higher strength than copper, good electrical and thermal conductivity, high corrosion resistance in the atmosphere and freshwater, and good plasticity, easy to cold and hot pressure processing, easy welding, forging and tin plating, no stress corrosion cracking.
-
Lue LisääPikakatselu
Brass Coil
Brass coil has excellent plasticity (best in brass) and high strength, good machinability, easy to weld, very stable to general corrosion, but prone to corrosion cracking; brass coil is copper and the alloy of zinc is named for its yellow color.
The mechanical properties and wear resistance of the brass coil are very good, and can be used to manufacture precision instruments, ship parts, shells of guns, jne. Brass knocks up and sounds good, so instruments such as cymbals, cymbals, bells, and numbers are made of brass. According to the chemical composition, brass is divided into ordinary copper and special brass.
-
Lue LisääPikakatselu
Stainless Steel Foil
Stainless steel foils are thin strips of stainless steel that are less than 0.2 mm in thickness and less than 300 mm in width.
Stainless steel foils offer a variety of advantages, including chemical stability, high strength-to-weight ratio, electrical insulation and corrosion resistance.
Stainless steel foil is used in the production of heat exchangers, capacitors and fuel cells; as well as in medical equipment and food processing machinery.
Stainless steel foils are a versatile material with many advantages. Its high corrosion resistance, good thermal and electrical conductivities and its ductility makes it an excellent choice for a wide range of applications.
Stainless steel foil is available in several different grades. These include austenitic series, ferritic series, martensitic series, duplex and super duplex series. Each grade has different alloying elements that contribute to the properties of the foil.
The most common grades of stainless steel foils are 304 ja 316. These grades are supplied in thicknesses ranging from 0.009mm to 0.3mm. Other grades of stainless steel foil are also available upon request including 409, 430 and duplex 2205.
-
Lue LisääPikakatselu
Brass Sheet
Brass Sheet based on electrolytic copper, zinc and trace elements as its raw material, through processing by ingot, hot rolling, cold rolling, heat treatment, surface cleaning, leikkaaminen, finishing, and then packing. Material processes performance, plasticity, mechanical properties, korroosionkestävyys, performance and good tin.
It has been widely used in electrical, auto, communications, hardware, decoration and other industries.
- DIN2391 tarkkuusteräsputki
- EN10305-1/4 Tarkkuusteräsputki
- EN10305-2/3/5/6 Tarkkuusputket
- SAE-sarjan tarkkuusputket
- ISO8535-1 polttoaineen ruiskutusputki
- Yksi/Doulbe Wall Bundy -putki
- Höyrykattila & Paineteräsputket
- Saumaton hiottu/SRB-teräsputki
- Ruostumattomat kapillaariset teräsputket
- Saumattomat ruostumattomat putket & Putket
- Hitsatut ruostumattomat putket & Putket
- Injektio & Ohjauslinjan putket
- Nikkeliseosputket & Putket
- Ei-rautametalliset kapillaariputket
- Alumiiniputket & Putket
- Messinkiputket & Putket
- Kupariputket & Putket
- Titaaniputket & Putket
- Suulakepuristettu/hitsattu eväputki
- Ei-rautakäyttöinen tarkkuusputki
- Erikoismuotoiset teräsputket
- Metallinen kela/kalvo/arkki/nauha